NOTICE

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Window Handle Replacement

It's simple to repair a damaged window handle with the proper tools. It is important to know the type of handle and its spindle's length prior buying the replacement.

Older uPVC windows feature cockspur window handles which have an extension spur that can the lock of a wedge cockspur striker plate. They can be right-handed or left-handed and must be matched when replacing.

What type of lock and handle do I have?

There are a variety of upvc window handles and locks, each having their distinct advantages and functions. The type of handle that you choose will determine whether or not your locking mechanism is effective and if it is easy to open the windows. As time passes and with regular use, window handles made of upvc can become damaged or worn out, rendering them less effective and secure. In some cases they might even be completely removed. It is essential to fix your upvc window handles when you see them falling off. This will help prevent burglaries and will keep your home secure.

It's a task that virtually anyone can perform. You'll need a few tools, but with the proper knowledge, UPVC Window Handle Replacement it's simple and should take only a couple of minutes. You will need to be aware of the type of lock or UPVC Window Handle Replacement handle you have on your window. This will help you choose the correct replacement.

Inline Espagnolette Handles

These are the most common type of upvc handles and are usually located on the side of your window. They are flat and have a latch which engages the locking mechanism of the window frame. Inline upvc handles have a spindle that runs through the middle of the handle and into the window frame to operate the latch.

Cockspur Handles

They are typically found on older uPVC window frames and feature an unusual hook-shaped design. Cockspur handles are held to the frame of the window by one screw, and are less secure than other types of window handles.

Tilt and Turn Handles

The tilt and turn handles are different from other upvc handles because they can be rotated to open the window glass replacement near me and then tilted into the window to allow air circulation. They have a 7mm spindle on the back and are available both in left and right-handed versions.

When purchasing replacement handles made of upvc it is essential to check the spindle length since not all of them are the same size. Drop something in the middle of the hole to check the length. This is the largest spindle size that will fit your windows.

What is the spindle?

uPVC window handles function similarly like doors, turning the handle to activate a latch inside the frame. This unlocks the window to allow it to be closed and opened. The handles can become damaged, particularly if they're used frequently or exposed to harsh environments. This can leave you needing to replace your uPVC handles for windows as they may not operate the window correctly for a long time.

There are many different kinds of uPVC handles available comprising Espag, Cockspur and Spaded handles. These handles are designed in a variety of ways to fit into uPVC frames. Each handle type utilizes a different spindle to lock the window mechanism. This is why it is important to identify the kind of handle is installed on your uPVC window so you can find the right replacement.

The base section of the handle will tell you what kind of uPVC it is. There should be a "snap in' cover over one screw that holds the handle's base in the correct position. When you remove this cover you will be able to see the second screw that holds the base of the handle in place. Once both screws are removed you should be able to pull the handle away from the uPVC window.

After removing the uPVC handle, remove it from the locking mechanism. Note the length of the spindle. You'll need to buy a replacement handles for windows of the same length as the original handle and the locking device.

The spindle wears down and cannot operate the locking mechanism. This can be due to damage from constant use or a loosening of the locking mechanism or even corrosion that occurs over time. If this happens, you will have to replace both the window handle and locking mechanism to restore the full functionality of your uPVC Windows.

How do I take off the old handle?

Window handles can become damaged or broken over time. It is crucial to fix them as quickly as possible to ensure your safety. It is easy to replace a worn or damaged handle. The job can be completed in under a minute without the need of special tools.

The first step in removing the old handle is to remove the screw that is situated on the top of the base of the handle. Once the screw is removed, the handle will be pulled away. A second screw will be located at the bottom of the handle. This too can be removed. After these two screws are removed, the handle can be removed from the window's base.

After removing the old handle and fixing holes, align the holes of the new handle with the holes already present in the window frame. There might be a small cap or sticker on the new handle, so remove them if needed and then put the handle in the frame. Once the handle is in place, it is important to test that it works by turning the handle, and ensuring that the lock mechanism is activated.

Espag handles have a spindle which protrudes out of the handle and slot into the multipoint locking mechanism that is on the frame of the window. Cadenza windows have a blade with cut-outs that slot into the lock mechanism while Cockspur handles have a long nose that hooks over the frame's outer or transom bar cross-member within the window.

Once you have the new handle in place, you can insert the spindle inside the window lock and then tighten it down. Replace the snap-in cover and screw cap (if necessary) once the handle is securely fixed. Now that the handle is ready for use, you can open and close the window a couple of times to make sure it is working properly and securely.

How do I install the new handle?

It's not difficult to alter the handle on your windows made of uPVC. The procedure is easy. You'll need an screwdriver and a bit of patience. First, make sure the handle is not locked. Then, remove any visible screws. You could also replace them with screw caps. After removing the handle it is necessary to take a note of the length of the spindle that extends from the back of the handle. This is crucial since it will determine the type of handle you'll need to purchase.

Espagnolette handles are the most commonly used type of handle used on uPVC windows. They have a spindle which is inserted into the handle and acts as an internal locking mechanism within the frame of the window. Once the handle is turned it releases the latch on the window and allows it to open. Over time and through regular use, espagnolette handles may be damaged or destroyed, making it necessary to locate a replacement.

Cadenza handles are another type of uPVC window handle that is commonly used on tilt and turn windows. They feature an extended blade that works a multipoint locking mechanism within the window. They are generally more secure than espagnolette handles as they can only be opened from the inside. They can be replaced using the same method as you would do for handles made of espagnolette however, ensure that the new handle is angled, not flat.

After you have chosen the correct handle, simply align the new handle with the existing screw holes before screwing it in place. After that, you can put the screws on and test the new handle. This is accomplished by moving the handle from the locked to the unlocked position and vice versa a few times. If you have any issues, it could be beneficial to speak with a professional to see if they can assist you in solving the issue. They can often advise you on the best solution to resolve the issue in a speedy and effective way.